1. Welcome to The Salty Box, a forum to discuss everything related to Marine & Reef Fish keeping in a friendly surrounding.

    Your voice is missing! You will need to register to be able to join in discussions with others.

    We hope to see you as a part of our community soon

    Dismiss Notice

Salifert Nitrate Test Kit Instructions

Discussion in 'All Salifert Test Kit Instructions' started by TigerIssey, Oct 13, 2009.

Thread Status:
Not open for further replies.
  1. TigerIssey

    TigerIssey Registered

    Joined:
    Aug 1, 2009
    Messages:
    9,143
    Likes Received:
    3
    Description
    Nitrate Profi-Test

    • * When there are insufficient areas of a tank which are deprived of oxygen (anaerobic zones) or denitrification is not taking place properly, nitrate will build up. This can also happen in an aquarium where the biological loading on the system is causing an imbalance e.g. if there is excessive livestock for the aquarium volume or over feeding is occurring.
      * The build up of nitrate can result in unwanted algae growth and the slowing down of coral growth.
      * The nitrate concentration in a reef aquarium should be lower than 1 mg/L, although fish only aquariums would usually have a higher concentration.
      * Just as with nitrite, many nitrate test kits are prone to amine interference which can make the levels of nitrate appear much lower than they actually are.
      * The Salifert test kit does not suffer from such interference and gives accurate and quick results with a total testing time of less than 3 minutes.
      * The test kit’s range goes from a very low to a very high nitrate concentration (approx. 0.2 - 100 mg/L as total nitrate).
      * Sufficient for 50 tests.


    This test offers two ranges:
    Low range: 0.2 - 10 mg/L (ppm) as nitrate.
    Medium range: 2 - 100 mg/L (ppm) as nitrate.

    Clean test vial and scoop after use. Store this kit in a dry place.

    Warning!

    KEEP OUT OF REACH OF CHILDREN.

    Specifications

    Low range: 0.2 - 10 mg/L (ppm) as nitrate.
    Medium range: 2 - 100 mg/L (ppm) as nitrate.

    Procedure for both ranges:

    1. Fill test vial with 1mL of water.
    2. Add 1 level scoop of NO3-1 powder (compress this powder against the inner side of the powder container).
    3. Add 1 level scoop of NO3-2 powder and swirl gently (do NOT shake) for 30 seconds.
    4. Let it stand for 3 minutes.
    5. Color comparison:

    Medium Range:

    Place the test vial on the white part of the color chart and compare colors looking from the TOP. Use diffuse daylight when comparing colors.

    If the color corresponds to a value lower than 10mg/L nitrate then it might be better to compare colors as shown for the low range (see below).

    Low Range:

    If the medium range color comparison procedure gave a reading lower than 10mg/L then you can use the low range prodecure. This will increase the accuracy.

    The color for the low range procedure has to be compared by looking through the SIDE of the test vial.

    The white part of the color chart has to be held firmly against the opposite side of the test vial. Use diffuse daylight when comparing colors.

    The color is, by looking through the side, amplified by approximately 10 fold. For this reason you have to divide the color chart values by 10. For example 2 will become 0.2 and 50 will become 5.
     
Thread Status:
Not open for further replies.
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice